Fakulta strojní
Permanent URI for this community
Browse
Browsing Fakulta strojní by Issue Date
Now showing 1 - 20 of 70
Results Per Page
Sort Options
- ItemPružící podstavec sanitního lehátka s integrovaným tlumením(Technická Univerzita v Liberci, 2011-01-01) Kohl, Ondřej; Pešík, LubomírThis project is dealing with innovation support of ambulance couchette that consist in integration of springing mechanism into one shoulder of the support for increasing comfort of transported inmate. Resulting draft has been chosen on the basis of analysis five possible variants of solving. The chosen solution, considering space limitation, only minimally intervenes in cusrrent construction of couchette. Mechanism has been provi-ded with pneumatic drive for setting the height of couchette - valves that make it possi-ble to change stiffness of the system and adjustable inhibitor that enables to set value of attenuation of the system.
- ItemRekuperační výměníky(Technická Univerzita v Liberci, 2011-01-01) Veselý, Michal; Dvořák, VáclavThis work deals with the measurement and calculation of the heat recovery exchanger. This is a multi-plate and plate heat recovery heat exchanger with cross flow of work materials are also included numerical models used for flow visualization. The first part is an introduction to the problem of heat recovery and heat recovery equipment theoretical designs. The second part deals with possible methods for the measurement and creation of numerical models in Fluent. The third section focuses on the actual measurement and evaluation of the data.
- ItemKonstrukční řešení podávacího systému pro svorku TIM25(Technická Univerzita v Liberci, 2011-01-01) Kulič, Martin; Bílek, MartinThe objective of this bachelor´s thesis is to find new feeding system for specified part. There is made a brief description of some current feeding systems and their parameters, especially in the domain of assembly automats. In this thesis is made a selection of proper feeding system for specified part for assembly automat for clamp TIM25. Structural design and some calculations are included.
- ItemPřípravek na topografii kalených a tvrzených vrstev nedestruktivními metodami(Technická Univerzita v Liberci, 2011-01-01) Růžička, Ondřej; Skrbek, BřetislavThe work for this diploma focuses on the topic and possibility of using non-destructive testing for the determination of topography of hardened layers of engine parts. To ensure repeated accuracy and reproducibility of measurement by these methods, a manual positioning preparation was designed and constructed to fix and position the measuring equipment and to precisely fit the measured engine part into position. For this work I used a cam-shaft from engine TEDOM as a typical engine part. Applying this method for regular daily checks in an engineering company, I also included a preliminary design of the computer operated automatic positioning preparation.
- ItemVariabilní měřící prostor pro supersonický aerodynamický tunel(Technická Univerzita v Liberci, 2011-01-01) Stupka, Oldřich; Dvořák, VáclavDiploma thesis deals with design, construction and testing of a variable test section. For its initial operations, three different nozzles for Mach numbers 1.4, 1.8 and 2.2 were made. These nozzles were designed using the method of characteristics. A Part of this work was to design and build a program to calculate the shape of jets using this method. Proposed profiles were simulated in software Fluent to verify the validity of the method of characteristics. During the experimental measurements in the laboratory of high speed in the Institute of Thermodynamics AVČR, images of the flow field using the colour schlieren method was taken. These were compared with numerical simulations and calculations using 1D method.
- ItemKonstrukce prototypu CNC stroje pro laserové řezání plechů(Technická Univerzita v Liberci, 2012-01-01) Tauchman, Jan; Zelený, PetrThis diploma thesis deals with design of CNC prototype machine, which will be used for metal sheets laser cutting at the Department of manufacturing systems. Construction of machine frame made of aluminum profiles, and connection of motion system and laser head is described here. The thesis also deals with calculation of applied drives. The examples of commercially produced machines similar to the designed one are also listed here.
- ItemNávrh mechanismu pro výrobu textilních filtračních vložek z netkané textilie tvořené nanovlákny(Technická Univerzita v Liberci, 2012-01-01) Svoboda, David; Kopal, JaroslavThe topic of my thesis is a fabrication facility design that would make non-woven fabric formed nanofibers produced firmly fixed filter element. This work deals withwhat the best possible alternative solutions. In the first part of the work is carried out research ways of processing fabric or paper in a similar product like the shape of the proposed filter. Another part deals with various theoretical principles of problem solving. In the practical part of thedesign is broken down and processed by optimum design parameters for the proposed facility cartridges. The work also includes technical documentation of the proposed facility.
- ItemAutomatizace obsluhy kartáčovacího rámu(Technická Univerzita v Liberci, 2012-01-01) Bali Šoltés, Petr; Zelený, PetrIn the beginning of thesis is introduced original concept of brush frame and other competitors products on maintenance of synthetic turf. The analysis of possible solutions was performed with regords to easy handling, price and production technology. Then two options of new brush frame are designed. Main objective of thesis is to automate and therefore make manipulation with this device easier.
- ItemAdaptivní chapadlo s poddajnými úchopnými prvky(Technická Univerzita v Liberci, 2012-01-01) Mikan, Tomáš; Novotný, FrantišekPředmětem předkládané bakalářské práce je prozkoumání možností tvarově poddajného uchopování. Na základě rešerše se práce zabývá návrhem koncepčního řešení tvarově poddajných úchopných prvků a návrhem jeho konstrukčního řešení, které bude možno aplikovat pro komerčně dodávaná chapadla různých typů. Součástí práce je také navržení testovacího zařízení a ověření funkčnosti navrhovaného řešení.
- ItemÚprava geometrie ohýbacího nástroje pro výrobu blatníku manipulačních strojů(Technická Univerzita v Liberci, 2012-01-01) Kirschner, Vít; Solfronk, PavelThis thesis deals with the modification of the bending tool geometry for production handling machines fender. The requirement for the bending tool shape change results from unsatisfactory dimensional accuracy of existing products. As the consequence of variations of production tolerances there is necessity to include other technological operations. The measuring of tested material mechanical properties by using a static tensile test is carried out in the thesis experimental part. Moreover, the actual real dimensions of tool and real stamping were determined by using non-contact optical 3D scanner REVscan. The bending tool shape change was carried out by numerical simulation at software PAM-STAMP 2G. To verify the applicability of this solution there was created the comparative numerical simulation of the technological process for production forklift fender under the respecting all process conditions. On the basis of numerical simulation was carried out a proposal for shape change of the bending tool in the CDS holding Company Ltd.
- ItemInovace stropní konzole osobního automobilu Ford(Technická Univerzita v Liberci, 2012-01-01) Zikmund, Petr; Fliegel, VítězslavDiplomová práce se zabývá inovací stropní konzole osobního automobilu Ford. Práce obsahuje kombinované řešení vnitřního komunikačního zrcátka a odkládací schránky na brýle. Inovace byla provedena s ohledem na zákazníka a jeho požadavky na prémiovou výbavu. Pro celý proces návrhu výrobku až po zkonstruování bylo využito metod inovačního inženýrství. Z navržených konceptů byla vybrána vítězná varianta a byla optimalizována z hlediska metod DFX, FMEA a MKP.
- ItemZařízení pro intenzivní míchání skloviny v malé pánvové peci(Technická Univerzita v Liberci, 2012-01-01) Stloukal, Tomáš; Matoušek, IvoThe bachelor work deals with the design and construction of an equipment for an intensive glass melt stirring in a new type of a small pot furnace. The design and construction is based on a long-time personal experience with pot furnaces operations. Knowledge and development trends gained during my bachelor studies are included. The submitted work gives a summary of literal research dealing with used solutions and describes calculation and experimental results necessary for designing a homogenization equipment. Different solutions of the homogenization equipment are presented and a chosen design is worked out in details. A remarkable increase of the glass melt homogeneity in a small pot furnace can be achieved using this design.
- ItemTrubkové výměníky tepla voda-vzduch(Technická Univerzita v Liberci, 2012-01-01) Jonáš, Petr; Dvořák, VáclavThe main point of this thesis was to investiged possibilities of using CFD methods for design of heat exchangers. Detail model of finned tube bank was made and the numerical simulation was applied to it. Geometry of detail model was gradually simplified and results of each numerical simulation were compared with detail model. Analytical calculations and experimental measurement were performed to prove results aquired by numerical simulation. Evaluation of results aquired analytically, experimentally and with use of CFD methods was made in conclusion.
- ItemStudium povrchových struktur vybraných přírodních objektů a možnosti vytváření jejich analogií(Technická Univerzita v Liberci, 2012-01-01) Ron, Jiří; Kroisová, DoraThis thesis gives attention to the area of biomimetics, a new interdisciplinary branch observing useful properties of nature which it tries to understand and transfer to technical practice. The range of biomimetics is very wide, this thesis gives attention to the so called lotus effect characterised by water-repellency and the ability of self-cleaning. The aim of the thesis was to observe the surfaces structure of chosen plants with lotus effect. On the basis of these observations have been documented structures of these object and with the aid of image analysis have been measured their characteristic dimensions. WIth the help of these dimensions have been created models of nature objects and their analogies which should have similar properties like natural objects. These patterns may serve as a basis for manufacturing of surfaces with lotus effect.
- ItemTechnologická hlavice průmyslového robotu pro opracování plochého skla(Technická Univerzita v Liberci, 2013-01-01) Fikar, David; Novotný, FrantišekCílem diplomové práce je návrh konstrukčního řešení technologické hlavice průmyslového robotu pro opracování plochého skla. Konstrukce hlavice pracuje na principu mechanického matování kartáči s brusnými zrny syntetického diamantu. Práce předkládá rozbor budoucího vývoje této technologie. Dále jsou zpracovány konstrukční návrhy hlavice a koncepce instalace hlavice do systému s průmyslovým robotem. Součástí práce je také stanovení technických podmínek pro efektivní využití této technologie, které byly zpracované na základě měření funkčního vzorku. Výkresová dokumentace konstrukčního návrhu je přiložena k práci.
- ItemKonstrukce rotoru s výkyvnými kyvetami u přístroje pro medicínskou diagnostiku.(Technická Univerzita v Liberci, 2013-01-01) Baťka, Ondřej; Beran, JaroslavTato bakalářská práce se zabývá konstrukcí rotoru u laboratorní centrifugy určené pro medicínskou diagnostiku. Podstatou práce je návrh rotoru s kyvetami, které jsou rotačně uloženy, což umožňuje jejich kyvný pohyb a zajišťuje vodorovnou polohu při odstředění. Důležitým kritériem je požadované odstředivé zrychlení při daných otáčkách rotoru. Vzhledem k vysokému provoznímu zatížení rotoru je třeba podrobit konstrukci pevnostní analýze pomocí metody konečných prvků prostřednictvím softwaru Pro/Mechanica. Závěr se zabývá, modální analýzou, návrhem uložení rotoru na hřídel servopohonu a vyhodnocením získaného odstředivého zrychlení.
- ItemNávrh pneumatických pohonů pro jednoúčelové zkušební zařízení a rozbor bezpečnosti(Technická Univerzita v Liberci, 2013-01-01) Minařík, Tomáš; Lachman, MartinPráce shrnuje informace o používaných pneumatických prvcích - válce, ventily, šroubení, hadice, jednotky pro úpravu vzduchu, navrhování pneumatických obvodů. Zabývá se návrhem pneumatického obvodu.
- ItemInovace zařízení pro upevnění záchranného člunu(Technická Univerzita v Liberci, 2013-01-01) Kratochvíl, Jaroslav; Pešík, LubomírTato diplomová práce se zabývá návrhem inovovaného zařízení pro zajištění záchranného člunu na lanech spouštěcího navijáku na lodní palubě. Hlavním avšak ne jediným parametrem, který byl inovací zlepšen, je síla potřebná k uvolnění člunu pod plným zatížením. Obsahem práce je rozbor stávajícího zařízení, dále návrh pěti konceptů inovovaného zařízení a výběr nejvhodnějšího konceptu. Vybraný koncept je pak optimalizován a zpracován až po výkresovou dokumentaci zařízení.
- ItemPlazmové modifikace povrchu exponovaných dílů jaderné elektrárny(Technická Univerzita v Liberci, 2013-01-01) Horák, Martin; Louda, PetrTato bakalářská práce se zabývá problematikou plazmových modifikací povrchů exponovaných dílů plánovaných jaderných elektráren. Teoretická část se zabývá rozdělením jaderných reaktorů současných a budoucích a také přehled vysokoteplotních slitin, které by mohly být v praxi využity pro tyto účely. V rešerši jsou popsány zvolené vysokoteplotní vrstvy, které se pomocí plazmových modifikací povrchů mohou nanášet. Praktická část obsahuje výzkum a výsledky experimentů, které ověřily odolnost a charakteristické vlastnosti vrstev v závislosti na tepelném ovlivnění.
- ItemKonstrukce formy pro 2K proces vstřikování(Technická Univerzita v Liberci, 2013-01-01) Šorf, Ondřej; Lenfeld, PetrTato diplomová práce se zabývá návrhem a konstrukcí 2K vstřikovací formy pro vybraný plastový díl. První část (rešeršní část) popisuje teoretické znalosti o procesu vstřikování včetně vícekomponentního vstřikování a konstrukce forem pro tyto procesy. Druhá část práce obsahuje návrh plastového dílu, simulaci vstřikování, návrh a konstrukci formy, popis a vysvětlení konstrukčních řešení provedených pro 2K vstřikování. Příloha této práce obsahuje výkresy sestavy formy a výkresy součástí a další dokumenty. Tato diplomová práce byla vypracována v rámci řešení projektu SGS 28005.