Fakulta strojní
Permanent URI for this collection
Browse
Browsing Fakulta strojní by Issue Date
Now showing 1 - 20 of 10244
Results Per Page
Sort Options
- ItemExpertní diagnostický systém Advisor(2000) Blažek, Radoslav
- ItemExperimentální ověřování vlivu řezných podmínek u matematického modelu procesu broušení(2001) Bílek, PetrPráce se zabývá návrhem metodiky zkoušek pro ověřování matematického modelu procesu broušení, realizací experimentů na brusce pro rovinné broušení obvodem kotouče BPH 20, porovnáním výsledků reálného a simulovaného proušení a návrhem opatření ke zpřesnění matematického modelu. Dále obsahuje analýzu ověřované metody matematického modelování kinematiky procesu broušení včetně analýzy vstupních dat modelu.
- ItemBudič vibrací pro zkoušení mechanických soustav(2003) Sajdl, Jan
- ItemAplikace plazmových nástřiků ze účelem snížení koeficientu tření a snížení lepivosti lepidla na dopravních válcích(Technická Univerzita v Liberci, 2004) Havel, Václav; Louda, PetrThe present study is concerned with the requirement of the firm ONTEX s.r.o. ( Ltd. ) to devise a new lining of the compression rollers the characteristics of which should be equal to the lining employed now. The new lining ought to be fabricated by means of plasma coating. The lining used at present has been analysed in detail, and a similar lining has been created with the assistance of a special manufacturer. A further objective of the study is the comparison, and eventually, a proposal of sprayed plasma coatings serving to devise the co-efficient of friction, to be employed in the firm indicated above.
- ItemChování kondenzačního kotle při ohřevu TUV v průtokovém výměníku(Technická Univerzita v Liberci, 2005) Stanečka, Tomáš; Novotný, PetrThis work is intended on behaving of gas condensing boiler during heating of warm water. In its first part it is engaged in gas boilers, their perspectives, construction, used technical improvements, especially condensing technology. Here is outline of parameters and functions of boiler Vitodens 200 from Viessmann. The second part content problems of heat exchanger their classification and basic calculation relations. The third part is set to measurement of dynamic characteristics of exist gas boiler (Viessmann Vitodens 200) during different flow rates of warmed-over water through heat exchanger.
- ItemVliv parametrů plazmové nitridace materiálů 42CrMo4, 34CrMo4 a 50CV4TSQ na povrchovou tvrdost nitridační vrstvy(Technická Univerzita v Liberci, 2005) Barák, Pavel; Daďourek, KarelThis thesis concerns with effect of characteristics of plasma nitration on materials 42CrMo4, 34CrMo4 and 50CV4TQS on surface hardness of nitriding layer. On these materials was perform five different processes of plasma nitration. Then was perform follow-up evaluation of samples from the aspect of achieved results and then were devise optimal parameters of plasma nitration by these materials: temperature - 491-494 gr.C, time - 15 hours.
- ItemSkladové hospodářství - řešení výstavbou nové haly v Produkt systém, s.r.o. Sušice(Technická Univerzita v Liberci, 2005) Žíla, Martin; Frinta, JanThe document concerns with solution of one the production section in company Product System s. r. o. in Sušice. It deals with initial consideration and proposing the solution of storing for the production of components for the company SIEMENS. The solutions are to meet conditions of the customer. Conditions are fluency and reliability of the supply and of the production.
- ItemVliv parametrů kataforézní lázně na penetraci profilů(Technická Univerzita v Liberci, 2005) Talián, Radoslav; Odehnalová, DanielaBakalářská práce je zaměřena na problematiku kataforézy v praxi, konkrétně na vliv parametrů kataforézní lázně na penetraci profilů.Hlavním cílem práce je zjistit závislost penetrační schopnosti barvy na jejích parametrech; především na teplotě barvy, na množství rozpouštědel a na čase povlakování.
- ItemRekuperační výměníky tepla s křížovým proudem(Technická Univerzita v Liberci, 2005) Procházka, Josef; Olehla, Josef
- ItemInovace ventilátorové trati(Technická Univerzita v Liberci, 2005) Šrámek, Ladislav; Novotný, PetrThe aim of this work was to propose the innovation of ventilator line in the laboratory of air-conditioning technique, to change power drive of ventilator and to propose a method of data logging. A substantial part of work was measurement of ventilator characteristic. It carried out first on ventilator line with an original direct-current motor powered by Ward-Leonard aggregate and after power drive change on ventilator line with an induction motor powered by frequency charger. The ventilator characteristic was measured at different revolutions that were operated by frequency of alternating current generated by the frequency charger. The measurements revealed a drawback of ventilator line consisting in too great pressure losses caused mainly by an orifice plate. They did not make it possible to realise complete measurement of ventilator characteristic. It was proposed to change the original orifice plate with diameter d = 54.77 mm for a new one with greater diameter (maximally d = 80.32). Such measure will decrease pressure losses several times. A method of automatic data logging for measurement on ventilator line was proposed. Necessary ranges of pressure sensors, temperature sensors, and air-humidity sensors used on ventilator line were estimated from supposed fluid-flow values and from the other conditions on the ventilator line. All sensors can be connected to the data logging system ADAM 5000 which is at disposal in the laboratory and which is connected to a computer. It would make it possible to process all measurement by computer.
- ItemMinitunel pro měření emisí tuhých látek(Technická Univerzita v Liberci, 2005) Štejnar, Radek; Moc, LubomírDiplomová práce shrnuje problematiku vzniku emisí tuhých látek ve výfukových plynech spalovacích motorů. V různých palivech porovnává obsah těchto částic, dále posuzuje používané měřící systémy a legislativní předpisy pro měření tuhých látek. Věnuje se vypracování postupu a software pro stanovení nejistoty měření tuhých látek. Zkoumá vliv provozních veličin motoru a podmínek odběru vzorku na hodnotu měrné emise tuhých látek motoru.
- ItemVazba akuastického výkonu a vibrací motoru(Technická Univerzita v Liberci, 2005) Hrubý, Petr; Němeček, Pavel
- ItemOptimalizace řízení toku materiálu na pracovišti kašírování insertů v GAT Turnov,s.r.o.(Technická Univerzita v Liberci, 2005) Haloun, Jan; Frinta, JanThis bachelor thesis focuses on the processing proposal of optimal material flow of the medallion coating process useing the analysis of the relationship between suppliers and customers. On the basis of this analysis volume of production and workplace check lay-out is proposed.
- ItemNávrh kryogenní nádoby na kapalný H2(Technická Univerzita v Liberci, 2005) Šumová, Lucie; Urbášek, Jan
- ItemOptimalizace procesu sběru dat ve výrobě(Technická Univerzita v Liberci, 2005) Mlejnek, Jan; Holub, LeošA scope of this dissertation is to compile an information about of modern and progressive methods of process automatization in production sphere as CIM and flexible dynamics automatization. The work also design new data model, outputs and process visualization used by Zinc plating line operators and discover a potential benefits by usage of collected data for other analyses in process of production management .
- ItemMěření charakteristik na odstředivém čerpadle(Technická Univerzita v Liberci, 2005) Švarc, Petr; Novotný, PetrHydraulic pumps are the part of hydraulic machines family and are commonly used in almost all branches of the industrial engineering. They have various possibilities of usage and therefore there is a huge amount of these machines all over the world. Lots of companies are focused on increasing output power as well as efficiency. One of the solutions how to reach higher efficiency is operating control and regulation of hydraulic pumps. The intentions of this work were to compare two different hydraulic pumps from the Wilo Company based on measuring of operating parameters. Two types of pumps " Stratos and Top-S " were chosen. The Stratos pump is electronically regulated, with possibility of settings of different operation modes. The Top-S pump is the common type without outer regulation. The operating parameters of the Stratos pump were measured during the different modes of the constant revolution, constant and variable differential pressure. The whole mechanism was vibrating during reducing of the flow's rate in the differential mode. These vibrations were measured as exact as measure equipment allowed. While measuring the power input and efficiency there were taken fifteen different measurements on the Stratos pump. The operating characteristics of the Top-S pump along with power input and efficiency were measured in three operating modes, which are available. Measured results were pictured into graphs and compared to each other. The Stratos pump shows higher efficiency. This pump is electronically controlled and it uses modern technologies. On the other hand it is more expensive than the Top-S pump.
- ItemSolární systém v energeticky úsporné budově(Technická Univerzita v Liberci, 2005) Bruckner, Petr; Unger, Jiří
- ItemVzduchotechnika pro válcovou brzdu osobních automobilů(Technická Univerzita v Liberci, 2006) Nýč, Petr; Scholz, Celestýn
- ItemKruhové seznamy a jejich použití(Technická Univerzita v Liberci, 2006) Brejcha, Martin; Věchet, VladimírThe aim of bachelor work is description data structure of circular list and possible operations with the list, including description of such operations. Choosen operations are realized with usage of C programming language. These functions are written in Region.c, which allow easily use of these functions for any programator.
- ItemMOTOR VM 650 SE VSTŘIKOVÁNÍM BENZINU DO SÁNÍ(Technická Univerzita v Liberci, 2006) Modrovský, Dušan; Laurin, JosefV úvodní části se diplomové práce jsou nejprve analyzovány stávající systémy vstřikování používané u motocyklů. V hlavní části práce je na základě této analýzy je zvolen vhodný systém vstřikování, pro nějž jsou zvoleny odpovídající komponenty a navržena zástavba komponentů do motocyklu VM 650 i jejich elektrické propojení. Rovněž je navrženo základní nastavení parametrů řídící jednotky pro zvolené komponenty. Navržený systém vstřikování je porovnán s výchozí karburátorovou verzí motoru. V závěru práce jsou navrženy některé další možné modifikace systému, z nichž nejvýznamnější je návrh hlavy motoru vhodné pro umístění vstřikovače a teplotního čidla.