Browsing by Author "Jirsák, Oldřich"
Now showing 1 - 19 of 19
Results Per Page
Sort Options
- ItemA 2-Dimensional Model Of The Mechanical-Properties Of Textiles(Textile Inst Intl Headquarters, 1993) Jirsák, Oldřich; Lukáš, David; Charvát, RichardA two-dimensional model of the mechanical properties of textiles is constructed, and the relations between model parameters and model behaviour are studied. The influence of the number of bonding sites in the model on stress-strain curves, on the CPU time consumption, and on the stability of model outputs is described. The methodology of computer-simulation methods in the study of textile mechanics is discussed.
- ItemConcentration of Taylor cones in needleless electrospinning(Technická Univerzita v Liberci, 2012) Görgec, Tugba Cigdem; Jirsák, OldřichIn this study, I have investigated the effect of Sodium Chloride (NaCl) salt on the spinnability of Polyethylene oxide (PEO) nanofibers and electrical current which is carried on jets via roller (needleless) electrospinning method. At first, solution properties were determined and then the results were analyzed. According to results, NaCl salt concentration has an important effect on conductivity, viscosity, spinning performance, fiber diameter and morphology. Conductivity and diameter of fibers increase with salt concentration. Polyethylene oxide with 0,3wt% NaCl gives the best spinning performance (throughput). During spinning process, process was recorded by camera and electrical current has been measured, afterwards, current, which was carried through per a jet was calculated. Eventually fabric throughput per current carried by Taylor cone was extrapolated
- ItemEffect of repeated loading on compressional rigidity of highlofts(Inst Chemical Fibres, 2002) Jirsák, Oldřich; Burian, Tomáš; Sanetrník, FilipHighloft textile materials are developed to replace non-recyclable foams for numerous end uses such as upholstery, mattresses, the automotive industry and many others. Better hygienic properties, recyclability and environmental friendliness are the main advantages of fibrous bulky materials when compared with foams. Nevertheless, the elastic properties of textile highlofts after repeated, long-term use and/or hot loading are still a weak point limiting their heavy-duty end-use, especially in the automotive industry, In the article, a method is suggested and tested to characterise the loss of compressional rigidity of bulky materials due to repeated loading during end-use. This method is used to evaluate the properties of fibrous highlofts developed with improved compressional properties.
- ItemElektrostatické zvlákňování modifikovaných polyakrylátů(Technická Univerzita v Liberci, 2007) Petríková, Lucia; Jirsák, OldřichCieľom diplomovej práce je nájsť spôsob výroby nanovláken z modifikovaných polyakrylátov procesom elektrostatického zvlákňovania. V teoretickej časti je vysvetlený princíp elektrostatického zvlákňovania, väčšina je venovaná prehľadu o akrylových materiáloch. Experimentálna časť sa zaoberá stanovením vhodnej koncentrácie kopolymérov v rozpúšťadle, skúmaním vplyvu obsahu soli na elektrickú vodivosť daných materiálov a priebeh elektrostatického zvlákňovania. Zaoberá sa tiež možnosťou náhrady pôvodného rozpúšťadla vhodnejším.
- ItemElektrostatické zvlákňování polyakrylonitrilu(Technická Univerzita v Liberci, 2007) Bábek, Pavel; Jirsák, OldřichV této diplomové práci je sledován vliv soli a relativní vlhkosti vzduchu na proces elektrostatického zvlákňování a vlastnosti výsledné nanovlákenné vrstvy. Zkoumaným materiálem byl roztok polyakrylonitrilu ve směsi s TEAB. Teoretická část popisuje proces elektrostatického zvlákňování a parametry použitých látek. Experimentální část se zabývá vlivem relativní vlhkosti vzduchu a soli při elektrostatickém zvlákňování polyakrylonitrilu. V experimentální části jsou dále popsána jednotlivá zařízení a měřící metody použité při měření. Cílem této práce byla optimalizace parametrů elektrostatického zvlákňování roztoku polyakrylonitrilu ve směsi s TEAB pro výrobu nanovlákenných vrstev metodou Nanospider.
- ItemElektrostatické zvlákňování polyuretanu(Technická Univerzita v Liberci, 2007) Mistr, Lukáš; Jirsák, OldřichTato diplomová práce se zabývá optimalizací elektrostatického zvlákňování PU metodou NANOSPIDER. Teoretická část práce je zaměřena na současný stav vývoje elektrostatického zvlákňování polymerů, na popis procesních parametrů, materiálových vlivů a na charakterizaci polymerních nanovláken. V experimentální části práce jsou zkoumány vliv soli na elektrickou vodivost, optimální podmínky a parametry při elektrostatickém zvlákňování roztoku PU v DMF. Experimentální část se dále zabývá vlivem relativní vlhkosti na elektrostatické zvlákňování, na výsledný produkt a na produkci zvlákňovacího zařízení. Cílem je nalézt optimální koncentrace roztoku PU s přídavkem soli, parametry a podmínky zvlákňovacího procesu, z hlediska produkce zvlákňovacího zařízení a kvality vyrobené nanovlákenné vrstvy.
- ItemElektrostatické zvlákňování polyuretanů pro medicínské aplikace(Technická Univerzita v Liberci, 2007) Súkeníková, Michaela; Jirsák, OldřichTáto práca sa zaoberá elektrostatickým zvlákňovaním medicínskych polyuretánov. Cieľom práce je nájsť vhodný polyuretánový materiál pre spracovanie technológiou elektrostatického zvlákňovania. Teoretická časť je prevážne venovaná vysvetleniu princípu elektrostatického zvlákňovania a prehľadu polyuretánových materiálov. V experimentálnej časti práca skúma vplyv soli a úpravy sulfonáciou na vlastnosti roztokov a vytvorených nanovláknových vrstiev. Ďalej sa zaoberá stanovením vplyvu procesných parametrov na zvlákniteľnosť.
- ItemImprovements in compressional properties of highlofts(Inst Chemical Fibres, 2003) Jirsák, Oldřich; Burian, Tomáš; Sasková, PavlínaOne new type of matrix fibres and two types of bi-component bonding fibres of the Teijin company Japan have been tested as raw material for manufacturing highloft textile materials. The fabrics obtained were compared with those made of commonly used fibres. Simultaneously, the properties of cross-laid and perpendicular-laid fabrics made of the fibres mentioned above were compared with those of polyurethane foam. Significant improvements in the compressional properties of fibrous highlofts were achieved by using the newly developed Japanese fibres, due to the perpendicular orientation of these fibres in comparison with conventional cross-laid fabrics.. The contributions of the new fibre materials together with the upright fibre position in highlofts proved that the resulting compressional properties of fabrics are close to those of polyurethane foams. This opens up more opportunity for the utilisation of fibrous highlofts in specific products, and allows us to exploit their advantages.
- ItemInfluence of Salts on Electrospinning of Aqueous and Nonaqueous Polymer Solutions(Technická Univerzita v Liberci, 2015) Yalcinkaya, Fatma; Yalcinkaya, Baturalp; Jirsák, OldřichA roller electrospinning system was used to produce nanofibres by using different solution systems. Although the process of electrospinning has been known for over half a century, knowledge about spinning behaviour is still lacking. In this work, we investigated the effects of salt for two solution systems on spinning performance, fibre diameter, and web structure. Polyurethane (PU) and polyethylene oxide (PEO) were used as polymer, and tetraethylammonium bromide and lithium chloride were used as salt. Both polymer and salt concentrations had a noteworthy influence on the spinning performance, morphology, and diameter of the nanofibres. Results indicated that adding salt increased the spinnability of PU. Salt created complex bonding with dimethylformamide solvent and PU polymer. Salt added to PEO solution decreased the spinning performance of fibres while creating thin nanofibres, as explained by the leaky dielectric model.
- ItemLineární útvary pokryté nanovlákny(Technická Univerzita v Liberci, 2013) Sanetrník, Filip; Jirsák, OldřichTato bakalářská práce se věnuje textilním lineárním útvarům obsahujícím nanovlákna. V teoretické části studuje a kriticky hodnotí dosavadní výsledky vývoje těchto útvarů, popisuje technologii a zařízení k výrobě těchto útvarů a definuje nezávislé a závislé proměnné procesu jejich výroby. V praktické části popisuje sérii experimentů zaměřených na studium vztahů mezi parametry ochranné bandáže nanovlákenného povlaku a plněním její funkce.
- ItemOn the Nature of Electric Current in the Electrospinning Process(Hindawi Publishing Corporation, 2013) Yalcinkaya, Baturalp; Yener, Fatma; Jirsák, Oldřich; Cengiz-Callioglu, FundaThe electric currents between electrodes in the electrospinning process are based on the movement of charge carriers through the spinning space. The majority of the charge carriers are formed by ionization of the air close to the metallic needle and to the polymer jet. The salt contained in the polymer solution contributes to the concentration of charge carriers, depending on its amount. The conductivity of polymer jets does not significantly affect the current since the jets do not link the electrodes.
- ItemPermanently corona charged filter materials of staple fibers(1997) Kolínová, Marcela; Jirsák, Oldřich; Wadsworth, L.Permanent electrical charging of fibrous filter materials by corona is one of the ways to increase filtration efficiency without increase in the pressure drop. The authors present teoretical and experimental knowledge of charging process. Charging of various fibrous materials and their surface finish are the topics described in a part "Experimental". Various fibrous materials are corona charged by TANRET METHOD. The results of the experiments and new arising questions Írom the experiments are discussed in cons|usion.
- ItemPolopropustné nanovlákenné membrány pro oděvní účely(Technická Univerzita v Liberci, 2010) Knížek, Roman; Jirsák, OldřichThe main goal of this graduation theses was the effort of formation of nanofibrous membrane, which can be used for clothing industry together with 100 per cent of wind resistence , very good permeability and a high water column. Separate functions of present new- fashioned membranes are attended in the introduction and the examples of some significant producers are stated here, too. There are observations of polyurethane chemistry, lamination and comfort of textiles in the theoretical part, first of all from the point of view of permeability. The particular procedures of production of nanofibrous membrane are mentioned in the experimental part of this theses including the reached values and comparation with those of competitive microporosity membrane of Gore-tex Company. Conclusion contains the commentary to the achieved results.
- ItemPolyamic Acid Nanofibers Produced by Needleless Electrospinning(Hindawi Publishing Corporation, 2010) Jirsák, Oldřich; Sysel, Petr; Sanetrník, Filip; Hrůza, Jakub; Chaloupek, JiříThe polyimide precursor (polyamic acid) produced of 4, 4'-oxydiphthalic anhydride and 4, 4'-oxydianiline was electrospun using needleless electrospinning method. Nonwoven layers consisting of submicron fibers with diameters in the range about 143-470 nm on the polypropylene spunbond supporting web were produced. Filtration properties of these nanofiber layers on the highly permeable polypropylene support-namely filtration effectivity and pressure drop-were evaluated. Consequently, these polyamic acid fibers were heated to receive polyimide nanofibers. The imidization process has been studied using IR spectroscopy. Some comparisons with the chemically identical polyimide prepared as the film were made.
- ItemRelation between needle and needleless electrospinning(Technická Univerzita v Liberci, 2011) Mazari, Adnan Ahmed; Jirsák, OldřichAbstract This Thesis predict a relation between needle and needle-less electrospinning ,as the needle-less or roller electrospinning is a time consuming and expensive procedure .so Poly (ethylene oxide ) with different molecular weight ,concentration and additives was tested on needle and needle-less elctrospinning with changing solution and process parameters (Molecular weight,voltage supply ,distance between electrodes, addition of NaCl-salt) whereas the ambient parameters (temperature and humidity )were kept constant. The results were examined on SEM and shows a great relationship between needle and needle-less electrospinning particularly in terms of spinnability,fiber quality ,non-fiborous area ,fiber diameter, fiber diameter distribution and throughput. The result are usefull in predicting the behavior of polymers in needle-less electrospinning with results from needle electrospinning.
- ItemStruktura a vlastnosti netkaných textilií(Technická univerzita v Liberci, 1990) Krčma, Radko; Hanzl, Jaroslav; Hes, Luboš; Charvát, Bohuslav; Charvát, Richard; Chrpová, Eliška; Jirsák, Oldřich; Kalousek, Zdeněk; Košková, Bohumila; Krebsová, Milada; Lukáš, David; Martinová, Lenka; Přívratská, Jana; Sodomka, Lubomír; Viková, Martina; Katedra netkaných textiliiZpráva shrnuje výsledky řešení problematiky struktury & vlastností netkaných textilií ze období let 1985 - 1990. Týká se diagnostiky textilií různými metcdRcai, zvláště laserovou a metodou mikromech»no3kopie. Výzkum zkušebních metod zahrnuje metody směřující k identifikaci distribuce pojiva vnáóeného v různých formách. Dále tepelná B teplotní měření včetně měřící techniky. Pokouáí se analyzovat vztahy mezi strukturou, podmínkami výroby a vlastnostmi netkaných textilií. Využívá filosofie modelování, která umožňuje výstižněji charakterizovat parametry struktury a hledat vazby mezi nimi, vlastnostmi a technologií výroby. Výsledkem prací teoreticky zaměřených jsou i návrhy na modifikace některých technologických priricipu, které jsou technologicky i konstrukčně rozpracovány a vedou k výraznému zlepšení některých uíitých vlastností. Jde o využití bodové distribuce pojivo, výrobu objemných textilií z kolmo vrstveného rouna a o armování propletu spleti smyček hedvábí.
- ItemStudy of the roller electrospinning with regard to roller movement(Technická Univerzita v Liberci, 2012) Kumalo, Mduduzi Blessing; Jirsák, OldřichThe objective was to control the thickness of the layer of the polymer solution onto a spinning roller. Therefore, the effect of the angular speed of the spinning roller and viscosity of the polyvinyl alcohol solution on the thickness of the layer of the polymer solution onto a spinning roller was investigated. The concentration of the solution was kept constant while changing roller angular speed; accordingly, the roller angular speed was kept constant while varying concentration and the thickness of the layer of the polymer solution was measured, respectively. Sodium chloride was added into the solution to change viscosity of the solution. The effects of roller speed and viscosity were visually observed onto the roller surface by video camera, analyzing the number of Taylor cones. Current test was also used to analyze the spinning progress. The properties of materials, such as spinning performance and fiber diameters were analyzed. It has been concluded that the thickness of the solution layer increases when the viscosity (as a function of concentration) of the solution increases. It has been also proven that the increase in the angular speed of the spinning roller causes an increase in the thickness of the solution layer onto the roller. Throughput of the product and diameters of nanofibers are both directly proportional to angular speed of the roller and viscosity of the solution. Therefore, the thicker is the layer of the polymer solution on top of the spinning roller the improved are fabric throughput and nanofiber diameter. These work proved that adding sodium chloride into polyvinyl alcohol to change its viscosity, affect, inversely, the electrospinning progress, fabric throughput and nanofibers diameters.Finally, the researcher adds roller movement and solution rheology into the family of parameters of roller electrospinning, since it affect both the spinning progress and produced material.
- ItemTepelně izolační vlastnosti nanovlákenných vrstev(Technická Univerzita v Liberci, 2007) Kocková, Helena; Jirsák, OldřichMěření tepelně izolačních vlastností je důležité pro řadu odvětví. Z hlediska prostupu tepla je nejvýznamnější radiační složka tepelného toku. Pro získání ucelené představy o tepelných projevech zkoumaného materiálu je důležité zjistit všechny tři části radiačního tepelného toku, kterými jsou emisivita, transmisivita a reflektivita, v jednom kroku. Proto bylo snahou vyvinout jednoduchou metodu, která by měřila všechny tři vlastnosti najednou.
- ItemVlastnosti polyuretanových nanovlákenných vrstev(Technická Univerzita v Liberci, 2007) Nováková, Markéta; Jirsák, OldřichThis paper deals with properties of polyurethane nanofibrous layers from the point of view of their air permeability, water vapour permeability and water resistance. There were three types of nanofibrous layers used: the first one without any treatment, the second one with hydrophilic treatment by adding surface-active substance into the solution for electrospinning and the third type was hydrophobic by using plasma treatment. The introduction of this paper provides a list of polyurethane membranes occurring on the market and search of polyurethane membranes. The theoretical part contains the method of production of nanofibrous layers, the material properties, the sorptive properties of fibres and methods of fabric assessment. The experimental part contains a description of an electrospinning device used for production of nanofibrous layers as well as the experimental process itself. Furthermore, there is a final result discussion. Lastly, an overall assessment of this paper is provided at the conclusion.