Bezkontaktní systém pro měření délky koncových měrek
Title Alternative:Contact–less System for Gauge Blocks Length Measurement
Loading...
Date
2016
Authors
Journal Title
Journal ISSN
Volume Title
Publisher
Abstract
Předkládaná habilitační práce poskytuje nové informace o možnostech využití principů
nízkokoherenční interferometrie pro měření délky koncových měrek.
Hlavním cílem předkládané práce bylo připravit bezkontaktní systém pro zavedení do
běžného provozu Českého metrologického institutu k měření délky koncových měrek.
K dosažení cíle bylo nutné zoptimalizovat bezkontaktní systém pro přímé potřeby
laboratorního měření, vytvořit kompletní dokumentaci k validaci dané metody měření tj.
stanovit nejistotu měření a následně metodiku (kalibrační postup) pro měření na daném
přístroji a porovnat nový systém se stávajícími systémy a jejich metodami měření běžně
využívaných v Českém metrologickém institutu, Oblastním inspektorátu Liberec.
Nezbytné základní pojmy týkající se řešené problematiky, vztahy a definice jsou
uvedeny v teoretické části práce. Do této části práce jsou zahrnuty přehledně informace
o interferenci, koncových měrkách a nejistotě měření. Dále jsou zde stručně uvedeny popisy
metod a zařízení pro měření délky koncových měrek na pracovišti Českého metrologického
institutu, Oblastního inspektorátu Liberec. Jedná se popis metody interferenční prováděné na
přístroji TESA NPL A.G.I. 300 a komparační prováděné na přístroji TESA–UPC. Nedílnou
součástí teoretické části jsou také informace vztahující se k základnímu popisu měření délky
koncových měrek na bezkontaktním systému.
Dosažení cíle je věnována kompletně celá experimentální část práce, která obsahuje
informace o optimalizaci systému z hlediska konstrukčního řešení, stanovení nejistoty měření
pro daný přístroj a metodu měření, kompletně zpracovanou metodiku pro měření délky
koncových měrek na daném přístroji (kalibrační postup). Pro ucelený pohled týkající se
zavedení systému je v poslední části řešení práce provedeno porovnání stávajících systémů
k měření délky koncových měrek v Českém metrologickém institutu, Oblastním inspektorátu
Liberec s bezkontaktním systémem.
The submitted habilitation thesis provides the new information about possibilities to utilize principles of the low–coherence interferometry for measurement the gauge block length. As a main purpose of the habilitation thesis there was preparation of the contact–less system for implementation into the Czech metrology institute common operation for measurement the gauge block length. To achieve purposes mentioned above there was necessary to optimize contact–less system for the direct needs of the laboratory measurement, to create complete documentation for validation the given measurement method i.e. to determine measurement uncertainty and subsequently methodology (calibration procedure) for its measurement on the given machine and to compare new system with the current systems and their measurement methodologies which are commonly used in the Czech metrology institute, Regional Inspectorate Liberec. All necessary basic terms those are related to the solving problem, equation and definitions are described in the theoretical part of habilitation thesis. In this part are digestedly summarized information about the interference, gauge blocks and measurement uncertainty. Moreover there are briefly mentioned descriptions of methods and devices for measurement the gauge blocks length in the workplace Czech metrology institute, Regional Inspectorate Liberec. More precisely, there is described both the interference method that is carried out on the device TESA NPL A.G.I. 300 and the comparative method that is done on the device TESA–UPC. As an integral part of the theoretical section there are also information regarding the basic description of the measurement gauge blocks length on the contact–less system. Completely the whole experimental part is about achieving the aim mentioned before. That is why it contains information about system optimization in light of its design solution, determination the measurement uncertainty for given device and measurement methodology, complete elaborated methodology for measurement the gauge blocks length on the given device (calibration procedure). To have the comprehensive view for the implementation of this system, in the last part of the habilitation thesis is carried out comparison of the current systems for measurement gauge blocks length in the Czech metrology institute, Regional Inspectorate Liberec with this contact–less system.
The submitted habilitation thesis provides the new information about possibilities to utilize principles of the low–coherence interferometry for measurement the gauge block length. As a main purpose of the habilitation thesis there was preparation of the contact–less system for implementation into the Czech metrology institute common operation for measurement the gauge block length. To achieve purposes mentioned above there was necessary to optimize contact–less system for the direct needs of the laboratory measurement, to create complete documentation for validation the given measurement method i.e. to determine measurement uncertainty and subsequently methodology (calibration procedure) for its measurement on the given machine and to compare new system with the current systems and their measurement methodologies which are commonly used in the Czech metrology institute, Regional Inspectorate Liberec. All necessary basic terms those are related to the solving problem, equation and definitions are described in the theoretical part of habilitation thesis. In this part are digestedly summarized information about the interference, gauge blocks and measurement uncertainty. Moreover there are briefly mentioned descriptions of methods and devices for measurement the gauge blocks length in the workplace Czech metrology institute, Regional Inspectorate Liberec. More precisely, there is described both the interference method that is carried out on the device TESA NPL A.G.I. 300 and the comparative method that is done on the device TESA–UPC. As an integral part of the theoretical section there are also information regarding the basic description of the measurement gauge blocks length on the contact–less system. Completely the whole experimental part is about achieving the aim mentioned before. That is why it contains information about system optimization in light of its design solution, determination the measurement uncertainty for given device and measurement methodology, complete elaborated methodology for measurement the gauge blocks length on the given device (calibration procedure). To have the comprehensive view for the implementation of this system, in the last part of the habilitation thesis is carried out comparison of the current systems for measurement gauge blocks length in the Czech metrology institute, Regional Inspectorate Liberec with this contact–less system.
Description
Subject(s)
interference, koncová měrka, nejistota měření, bezkontaktní systém, interferometry, gauge blocks, measurement uncertainty, contact–less system