Analýza procesních parametrů technologie Selective Laser Melting
dc.contributor | Koutný Daniel, doc. Ing. Ph.D. : 66797 | |
dc.contributor.advisor | Šafka Jiří, Ing. Ph.D. : 61635 | |
dc.contributor.author | Véle, Filip | |
dc.contributor.other | Henyš Petr, Ing. Ph.D.;Ackermann Michal, Ing. Ph.D. Konzultant : 62628;61392 | |
dc.date.accessioned | 2019-05-21T16:58:16Z | |
dc.date.available | 2019-05-21T16:58:16Z | |
dc.date.committed | 2019-5-15 | |
dc.date.defense | 2018-8-29 | |
dc.date.submitted | 2017-11-15 | |
dc.date.updated | 2018-12-10 | |
dc.degree.level | Bc. | |
dc.description.abstract | Cílem této bakalářské práce je analýza vstupních parametrů procesu SLM a posouzení jejich vlivu na výstupní strukturu materiálu. V této práci byly ovlivňovány dva parametry, a to výkon laseru a skenovací rychlost. Vyhodnocovanými parametry procesu byly porozita materiálu a tvrdost v daném řezu. Praktická část této práce byla rozdělena na tři části - analýzu vstupního prášku, aplikování metody DOE a využití statistické metody ANOVA pro zobrazení výsledků. Provedením použité metody bylo zjištěno, že největší vliv na konečnou porozitu a tvrdost má výkon laseru. Hlavním zjištěním této práce je fakt, že je možné využívat metody DOE pro analýzu vstupních parametrů pro SLM proces. Dále se ukazuje nutnost většího počtu replikací testu pro dosažení vyšší statistické významnosti ANOVA testu. | cs |
dc.description.abstract | The aim of this bachelor thesis is analysis of input parameters of SLM process and evaluation of their influence on output structure of the material. In this thesis, two main parameters - laser power and scanning speed - were affected during the tests. The porosity of material and hardness were chosen as output parameters. The practical part of this thesis was divided into the three parts - analysis of input powder, aplication of DOE method and using the ANOVA statistical method for plotting the results. With use of these methods, it was found out that the value of laser power influences both porosity and hardness in the most signifacant way. The main finding of this paper is that it is possible to use DOE for analysis of input parameters for the SLM proces. Another finding is that it is necessary to run more replications of the experiment in order to obtain more reliable data from ANOVA test. | en |
dc.description.mark | ||
dc.format | 60 s. | |
dc.format.extent | Ilustrace, Schémata, Grafy, Tabulky ROM | |
dc.identifier.signature | V 201900454 | |
dc.identifier.uri | https://dspace.tul.cz/handle/15240/152393 | |
dc.language.iso | cs | |
dc.relation.isbasedon | [1] MONTGOMERY, Douglas C. Design and analysis of experiments. John Wiley & Sons, 2017. ISBN-13 978-1118146927 | |
dc.relation.isbasedon | [2] YADROITSEV, Igor. Selective laser melting: Direct manufacturing of 3D-objects by selective laser melting of metal powders. Lambert Academic Publishing, 2009. ISBN-13 978-3838317946 | |
dc.relation.isbasedon | [3] BRYSON, William E. Heat treatment, selection, and application of tool steels. Hanser Gardner Publications, 2005. ISBN-13 978-1569903766 | |
dc.rights | Vysokoškolská závěrečná práce je autorské dílo chráněné dle zákona č. 121/2000 Sb., autorský zákon, ve znění pozdějších předpisů. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem https://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou https://knihovna.tul.cz/document/26 | cs |
dc.rights | A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act. https://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics https://knihovna.tul.cz/document/26 | en |
dc.rights.uri | https://knihovna.tul.cz/document/26 | |
dc.rights.uri | https://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf | |
dc.subject | Selective Laser Melting | cs |
dc.subject | SLM | cs |
dc.subject | Design of Experiments | cs |
dc.subject | DOE | cs |
dc.subject | Porozita | cs |
dc.subject | Tvrdost | cs |
dc.subject | Selective Laser Melting | en |
dc.subject | SLM | en |
dc.subject | Design of Experiments | en |
dc.subject | DOE | en |
dc.subject | Porosity | en |
dc.subject | Hardness | en |
dc.subject.verbis | strojírenské technologie | cs |
dc.title | Analýza procesních parametrů technologie Selective Laser Melting | cs |
dc.title | Analysis of processing parameters for Selective Laser Melting technology | en |
dc.type | bakalářská práce | cs |
local.degree.abbreviation | Bakalářský | |
local.degree.discipline | SI | |
local.degree.programme | Strojní inženýrství | |
local.degree.programmeabbreviation | B2301 | |
local.department.abbreviation | KSA | |
local.faculty | Fakulta strojní | cs |
local.faculty.abbreviation | FS | |
local.identifier.author | S17000317 | |
local.identifier.stag | 37437 | |
local.identifier.verbis | kpw06580952 | |
local.note.administrators | automat | |
local.poradovecislo | 454 | |
local.verbis.aktualizace | 2019-10-05 07:26:58 | cs |
local.verbis.studijniprogram | KSA Strojní inženýrství/Strojní inženýrství | cs |
Files
Original bundle
1 - 4 of 4
Loading...
- Name:
- BP_FilipVele.pdf
- Size:
- 21.95 MB
- Format:
- Adobe Portable Document Format
- Description:
- VSKP
Loading...
- Name:
- Vele.pdf
- Size:
- 145.19 KB
- Format:
- Adobe Portable Document Format
- Description:
- Posudek_vedouciho_VSKP
Loading...
- Name:
- Vele.pdf
- Size:
- 194.33 KB
- Format:
- Adobe Portable Document Format
- Description:
- Posudek_oponenta_VSKP
Loading...
- Name:
- ProtokolSPrubehemObhajobySTAG.pdf
- Size:
- 12.93 KB
- Format:
- Adobe Portable Document Format
- Description:
- Prubeh_obhajoby_VSKP