Průmyslový aplikátor pro látky v tubách
dc.contributor | Hejnová Monika, Ing. Ph.D. : 66753 | |
dc.contributor.advisor | Kovář Šimon, Ing. Ph.D. : 62087 | |
dc.contributor.author | Gabriel, Tomáš | |
dc.contributor.author | S16000332 | |
dc.date.accessioned | 2019-05-09T17:04:40Z | |
dc.date.available | 2019-05-09T17:04:40Z | |
dc.date.committed | 2018-5-21 | |
dc.date.defense | 2018-6-13 | |
dc.date.submitted | 2017-10-30 | |
dc.date.updated | 2018-12-10 | |
dc.degree.level | Ing. | |
dc.description.abstract | Tato diplomová práce je zaměřena na konstrukční návrh zařízení pro pneumatické vytlačování chemické látky z formátu tuby. Důvodem vzniku této práce je požadavek z průmyslu, kde takto hnané zařízení není k dispozici. V rešeršní části byly popsány aplikační pistole používané na dávkování látek. Dále zde byly popsány i jednotlivé druhy obalů. Byla zde uvedena kapitola věnující se manipulačnímu a zdvihacímu zařízení, na které bylo potřeba aplikátor zavěsit. V praktické části byly navrženy 3 varianty možného řešení. Z těchto 3 variant byla na základě vícekriteriální analýzy vybrána jedna. U té byla praktickou zkouškou ověřena funkce. Na základě experimentu byla zhotovena konstrukce zařízení určena pouze pro konkrétní rozměry tuby. V softwaru Creo Parametric byl vytvořen 3D model konstrukce, která slouží pouze pro kusovou výrobu a k ní byla zhotovena výkresová dokumentace. | cs |
dc.description.abstract | This diploma thesis focuses on the design of devices for pneumatic extrusion of chemical materials from the tube format. The reason for creating this work is a requirement from an industry because this device is not available there. In the research section, there are described applications of guns used for dosing of substances. In addition, the types of packaging have been described here. There was a chapter dealing with the handling and lifting device to which the applicator will be hang. In the practical part, 3 variants of a possible solution were proposed and one solution was selected by using the multi-criteria analysis. This feature has been verified by a practical test. On the basis of the experiment, the construction of the device was made only for the specific dimensions of the tube. In Creo Parametric software was created drawing documentation and a 3D model of construction, which can be used only for small production. | en |
dc.description.mark | ||
dc.format | 52 | |
dc.format.extent | - ROM Výkresová dokumentace | |
dc.identifier.signature | V 201900418 | |
dc.identifier.uri | https://dspace.tul.cz/handle/15240/152207 | |
dc.language.iso | cs | |
dc.relation.isbasedon | [1] H. Meerkamm. Technical pocket guide. University of Erlangen-Nuremberg. Schaeffler Technologies GmbH & Co.KG, 1st edition, March 2014. [2] R. Michael. Designing with Creo Parametric 3.0. SDCpublication. 2015. ISBN 9781585039807 [3] H. Meerkamm. Technical pocket guide. University of Erlangen-Nuremberg. Schaeffler Technologies GmbH & Co.KG, 1st edition, March 2014. | |
dc.rights | Vysokoškolská závěrečná práce je autorské dílo chráněné dle zákona č. 121/2000 Sb., autorský zákon, ve znění pozdějších předpisů. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem https://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou https://knihovna.tul.cz/document/26 | cs |
dc.rights | A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act. https://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics https://knihovna.tul.cz/document/26 | en |
dc.rights.uri | https://knihovna.tul.cz/document/26 | |
dc.rights.uri | https://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf | |
dc.subject | dávkovač | cs |
dc.subject | aplikátor | cs |
dc.subject | pneumatický pohon | cs |
dc.subject | tuba | cs |
dc.subject | dispenser | en |
dc.subject | applicator | en |
dc.subject | pneumatic power | en |
dc.subject | tube | en |
dc.subject.verbis | driving mechanism | en |
dc.title | Průmyslový aplikátor pro látky v tubách | cs |
dc.title | Industrial applicator for materials in tubes | en |
dc.type | diplomová práce | cs |
local.degree.abbreviation | Navazující | |
local.degree.discipline | TS2 | |
local.degree.programme | Strojní inženýrství | |
local.degree.programmeabbreviation | N2301 | |
local.department.abbreviation | KTS | |
local.faculty | Fakulta strojní | cs |
local.faculty.abbreviation | FS | |
local.identifier.stag | 37742 | |
local.identifier.verbis | kpw06576210 | |
local.note.administrators | automat | |
local.poradovecislo | 418 | |
local.verbis.aktualizace | 2019-10-05 07:26:53 | cs |
local.verbis.studijniprogram | KTS Strojní inženýrství/Konstrukce strojů a zařízení | cs |
Files
Original bundle
1 - 5 of 6
Loading...
- Name:
- DP_TG_prumyslovy_aplikator_pro_latky_v_tubach_2018.pdf
- Size:
- 12.54 MB
- Format:
- Adobe Portable Document Format
- Description:
- VSKP
Loading...
- Name:
- DPTomas_Gabriel_Vykresy_2018.pdf
- Size:
- 784.79 KB
- Format:
- Adobe Portable Document Format
- Description:
- VSKP
Loading...
- Name:
- Hodnotenie_veduceho_prace_GABRIEL.PDF
- Size:
- 1.51 MB
- Format:
- Adobe Portable Document Format
- Description:
- Posudek_vedouciho_VSKP
Loading...
- Name:
- Hodnotenie_oponenta_GABRIEL.PDF
- Size:
- 1.03 MB
- Format:
- Adobe Portable Document Format
- Description:
- Posudek_oponenta_VSKP
Loading...
- Name:
- ProtokolSPrubehemObhajobySTAG.pdf
- Size:
- 10.19 KB
- Format:
- Adobe Portable Document Format
- Description:
- Prubeh_obhajoby_VSKP