Vliv prostředí na vybrané vlastnosti dílů na bázi fotopolymeru zhotovené technologií PolyJet
dc.contributor | Kůsa Petr, Ing. Ph.D. : 62814 | |
dc.contributor.advisor | Běhálek Luboš, Ing. Ph.D. : 55398 | |
dc.contributor.author | Pich, Václav | |
dc.contributor.author | S16000287 | |
dc.contributor.other | Šafka Jiří, Ing. Ph.D. Konzultant : 61635 | |
dc.date.accessioned | 2019-05-09T17:00:46Z | |
dc.date.available | 2019-05-09T17:00:46Z | |
dc.date.committed | 2019-2-1 | |
dc.date.defense | 2018-6-14 | |
dc.date.submitted | 2017-11-1 | |
dc.date.updated | 2018-12-10 | |
dc.degree.level | Ing. | |
dc.description.abstract | Diplomová práce se zabývá studiem vlivů prostředí na vybrané mechanické vlastnosti dílů s ohledem na směr orientace vrstev zhotovených 3D tiskem technologií PolyJet. Prototypové díly byly zhotoveny s různými směry orientace vrstev a vystaveny standardnímu prostředí 23/50 dle ČSN EN ISO 291, prostředí zvýšené vlhkosti (relativní vlhkost 80 %) při teplotě 30 °C po dobu 2 týdnů a byly také exponovány teplotnímu zatížení až 100 °C po dobu 510 min. Hodnoceny byly základní mechanické charakteristiky fotopolymerů při tahovém, ohybovém a rázovém namáhání dílů. | cs |
dc.description.abstract | The diploma thesis is focused on studying the impact of ambient on the selected mechanical properties of parts affected by the directional orientation of layers made by the 3D printing Polyjet technology. The prototype parts were prepared with different layer orientations, and exposed to the standard ambient 23/50 by CSN EN ISO 291, the ambient with increased humidity (a relative humidity of 80%) at a temperature of 30 °C for 2 weeks, and exposed to a thermal load of up to 100 °C for 510 minutes. The primary mechanical properties of photopolymers evaluated during the testing were the tensile, bend and notched strains of evaluated parts. | en |
dc.format | 73 s. 66 413 znaků | |
dc.format.extent | ROM | |
dc.identifier.signature | V 201900392 | |
dc.identifier.uri | https://dspace.tul.cz/handle/15240/152181 | |
dc.language.iso | cs | |
dc.relation.isbasedon | [1] Gibson, I., Rosen, D.W., Stucker, B. Additive manufacturing technologies: 3D printing, rapid prototyping and direct digital manufacturing. ISBN: 9781493921126. | |
dc.relation.isbasedon | [2] Liu, D., Valencia, V. V., Badiru, A. B. Additive manufacturing handbook. CRC Press, Taylor and Francis Group, 2017. ISBN: 9781482264081. | |
dc.relation.isbasedon | [3] Grote, K.H., Feldhusen, J. Dubbel. Taschenbuch für den Maschinenbau. Berlin: Springer, 2011. ISBN 9783642173059. | |
dc.relation.isbasedon | [4] Mezinárodní normy. | |
dc.rights | Vysokoškolská závěrečná práce je autorské dílo chráněné dle zákona č. 121/2000 Sb., autorský zákon, ve znění pozdějších předpisů. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem https://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou https://knihovna.tul.cz/document/26 | cs |
dc.rights | A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act. https://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics https://knihovna.tul.cz/document/26 | en |
dc.rights.uri | https://knihovna.tul.cz/document/26 | |
dc.rights.uri | https://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf | |
dc.subject | 3D tisk | cs |
dc.subject | PolyJet | cs |
dc.subject | fotopolymer | cs |
dc.subject | vliv prostředí | cs |
dc.subject | 3D printing | en |
dc.subject | PolyJet | en |
dc.subject | photopolymer | en |
dc.subject | impact of ambient | en |
dc.subject.verbis | polymery | cs |
dc.subject.verbis | polymers | en |
dc.subject.verbis | trojrozměrný tisk | cs |
dc.subject.verbis | three-dimensional printing | en |
dc.title | Vliv prostředí na vybrané vlastnosti dílů na bázi fotopolymeru zhotovené technologií PolyJet | cs |
dc.type | diplomová práce | cs |
local.degree.abbreviation | Navazující | |
local.degree.discipline | ZP2 | |
local.degree.programme | Strojní inženýrství | |
local.degree.programmeabbreviation | N2301 | |
local.department.abbreviation | KSP | |
local.faculty | Fakulta strojní | cs |
local.faculty.abbreviation | FS | |
local.identifier.stag | 37799 | |
local.identifier.verbis | kpw06576184 | |
local.note.administrators | automat | |
local.poradovecislo | 392 | |
local.verbis.aktualizace | 2019-10-05 07:26:51 | cs |
local.verbis.studijniprogram | KSP Strojní inženýrství/Strojírenská technologie a materiály | cs |
Files
Original bundle
1 - 4 of 4
Loading...
- Name:
- DP_Pich.pdf
- Size:
- 3.06 MB
- Format:
- Adobe Portable Document Format
- Description:
- VSKP
Loading...
- Name:
- Pich_2.pdf
- Size:
- 1.36 MB
- Format:
- Adobe Portable Document Format
- Description:
- Posudek_oponenta_VSKP
Loading...
- Name:
- Pich_1.pdf
- Size:
- 144.59 KB
- Format:
- Adobe Portable Document Format
- Description:
- Posudek_vedouciho_VSKP
Loading...
- Name:
- ProtokolSPrubehemObhajobySTAG.pdf
- Size:
- 13.14 KB
- Format:
- Adobe Portable Document Format
- Description:
- Prubeh_obhajoby_VSKP