Characterization of optical fiber after surface modification

Title Alternative:Characterization of optical fiber after surface modification
dc.contributor.advisorMishra, Rajesh
dc.contributor.authorShukla, Anuj
dc.date2012
dc.date.accessioned2015-07-07
dc.date.available2015-07-07
dc.date.committed2012-05-09
dc.date.defense2012-05-28
dc.date.issued2012-01-01
dc.date.submitted2011-09-30
dc.degree.levelmgr
dc.descriptionkatedra: KTT; přílohy: CD ROM; rozsah: 80 s.cs
dc.description.abstractOptical fibers have been used principally for data transmission, since it offers fast connectivity, low cost, and high resistance to damage. The purpose of this research was not to evaluate the data capabilities of plastic optical fibers (POF) which transmits axially, but rather to exploit the ability of the fiber emit light through the side of the fiber. The uses of side emitting fibers in textile would prove to beneficial in several ways, few of them being the flexibility of the fiber for integration into fabrics, and possibly to mask this fiber like all others, with the aid of classical textile dyeing methods. The POF, with trade name Flexi was used in this case, because of its flexibility, and variation in diameters available on the market. Flexi cores were stripped from its cladding, and were dyed using a disperse dye, under various conditions including changing in dye concentration and dye time. Samples were then analysed for side emission of light with the use of Prototype 1, which was an instrument specifically designed for the measurement of this nature. The results showed that the dye penetration is dependent on the dye time, if dye concentration and temperature are kept constant. After 40minutes of dyeing, the fiber core showed an increase in side emission, with lower loss due to attenuation. Also excessive time in the hot conditions degraded the fiber, such that the fiber became very stiff and brittle. Fibers were also subjected to heat, in the form of boiling water bath, for selected periods of time, and it was found that the effect was similar to that of the prior experiments. Surface treatment of Flexi fibers were carried out using ethyl acetate as an etching agent, to possibly accept more disperse dye on the fibers surface. The results after dyeing showed a more than significant improvement in both side emission and attenuation of light. The influence of the illuminating source of the fiber also proved to be important, such that the side emission is dependent on the temperature of light from the source.en
dc.description.abstractOptical fibers have been used principally for data transmission, since it offers fast connectivity, low cost, and high resistance to damage. The purpose of this research was not to evaluate the data capabilities of plastic optical fibers (POF) which transmits axially, but rather to exploit the ability of the fiber emit light through the side of the fiber. The uses of side emitting fibers in textile would prove to beneficial in several ways, few of them being the flexibility of the fiber for integration into fabrics, and possibly to mask this fiber like all others, with the aid of classical textile dyeing methods. The POF, with trade name Flexi was used in this case, because of its flexibility, and variation in diameters available on the market. Flexi cores were stripped from its cladding, and were dyed using a disperse dye, under various conditions including changing in dye concentration and dye time. Samples were then analysed for side emission of light with the use of Prototype 1, which was an instrument specifically designed for the measurement of this nature. The results showed that the dye penetration is dependent on the dye time, if dye concentration and temperature are kept constant. After 40minutes of dyeing, the fiber core showed an increase in side emission, with lower loss due to attenuation. Also excessive time in the hot conditions degraded the fiber, such that the fiber became very stiff and brittle.Fibers were also subjected to heat, in the form of boiling water bath, for selected periods of time, and it was found that the effect was similar to that of the prior experiments. Surface treatment of Flexi fibers were carried out using ethyl acetate as an etching agent, to possibly accept more disperse dye on the fibers surface. The results after dyeing showed a more than significant improvement in both side emission and attenuation of light. The influence of the illuminating source of the fiber also proved to be important, such that the side emission is dependent on the temperature of light from the source.cs
dc.formattext
dc.identifier.urihttps://dspace.tul.cz/handle/15240/12316
dc.language.isoen
dc.publisherTechnická Univerzita v Libercics
dc.subjectoptical fibersen
dc.subjectpolymethyl methacrylateen
dc.subjectpmmaen
dc.subjectside emissionen
dc.subjectsurface treatmenten
dc.subjectdyeingen
dc.subjectoptical fiberscs
dc.subjectpolymethyl methacrylatecs
dc.subjectpmmacs
dc.subjectside emissioncs
dc.subjectsurface treatmentcs
dc.subjectdyeingcs
dc.subject.verbisdyeing of textileen
dc.titleCharacterization of optical fiber after surface modificationcs
dc.title.alternativeCharacterization of optical fiber after surface modificationen
dc.typeThesis
local.departmentKTTcs
local.facultyFakulta textilnícs
local.identifier.verbis463524
local.note.administratorsautomat-mix
local.verbis.aktualizace2019-10-05 06:22:46cs
local.verbis.studijniprogramKTT Textile engineering/Textile engineering-Textile technologycs
Files
Original bundle
Now showing 1 - 3 of 3
Loading...
Thumbnail Image
Name:
mgr_23663.pdf
Size:
1.94 MB
Format:
Adobe Portable Document Format
Description:
kvalifikační práce
Loading...
Thumbnail Image
Name:
Dipl_23663.pdf
Size:
352.52 KB
Format:
Adobe Portable Document Format
Description:
posudek oponenta
Loading...
Thumbnail Image
Name:
Dipl_236631.pdf
Size:
400.53 KB
Format:
Adobe Portable Document Format
Description:
posudek vedoucího