Browsing by Author "Kracík, Jan"
Now showing 1 - 6 of 6
Results Per Page
Sort Options
- ItemAerodynamické ucpání v nadzvukovém ejektoruKracík, Jan; ; Dvořák Václav, prof. Ing. Ph.D. Skolitel : 55439Práce se zabývá studiem proudění stlačitelné tekutiny v nadzvukových ejektorech s osově nastavitelnou hnací tryskou. V úvodní části je představeno téma práce a jsou uvedeny cíle výzkumu. Dále je zaměřena pozornost na teorii týkající se stlačitelného proudění a aerodynamického ucpání. Následuje teorie nadzvukových ejektorů a jejich návrhových metod. Jsou představeny dvě analytické metody používané pro návrh nadzvukových ejektorů, přičemž každá z metod vychází z jiných předpokladů. Další části se zabývají metodami numerického a experimentálního výzkumu. V práci je vyšetřován vliv provozních podmínek a osové vzdálenosti hnací trysky od směšovací komory na proudění v nadzvukovém ejektoru. Je blíže popsána struktura proudění uvnitř ejektoru a proveden rozbor z hlediska aerodynamického ucpání hnaného proudu. Jsou formulovány závěry a uvedeny přínosy práce včetně doporučení pro další výzkum problematiky.
- ItemExperimental investigation of centrifugal fans for personal protection equipment – effect of used 3D printing technologies(EDP Sciences, 2018) Dvořák, Václav; Kracík, Jan; Votrubec, Radek; Šafka, JiříThe aim of the research is experimental investigation of centrifugal fans for a personal protection equipment. The aim of the fan is to drive the contaminated air containing harmful or irritating particles through the filters and then into the mask of workers, such as a fireman, a labourer or a lab worker. The fan is measured on the test stand, the characteristics and performances are evaluated, i.e. the dependencies of the working pressure on the flow rate. The characteristics are measured for three constant speed settings. The characteristics of the wheels produced by the different 3D printing technology are compared. It is found that the production technology has only a minimal effect, the performance of the wheels is more influenced by the position of the impeller on the motor shaft and hence by the mutual position of the impeller and the diffuser.
- ItemIntroductory Numerical Study on Supersonic Ejector Working with R32(E D P SCIENCES, 17 AVE DU HOGGAR PARC D ACTIVITES COUTABOEUF BP 112, F-91944 CEDEX A, FRANCE, 2019) Vojta, Lukáš; Kracík, Jan; Dvořák, VáclavNowadays, there is an increasing demand for devices which work efficiently with the smallest possible consumption of energy. In this regard, incorporating ejectors seems to be an interesting choice. This paper describes the numerical analysis of the flow in a supersonic ejector working with R32 (difluoromethane) as the working fluid. The ejector geometry under investigation in this paper has already been experimentally analysed, however, air was used as the working fluid. Therefore, this paper deals with a numerical analysis of the same geometry but with a different working fluid. Furthermore, the design of the ejector enabled the adjustment of a particular distance of the motive nozzle from the beginning of the mixing chamber, i.e. the nozzle exit position (NXP). This work examines the ejector numerically for eleven values of back-pressure with the NXP of two millimetres; consequently, the performance line of the ejector with fixed boundary conditions at both inlets was obtained. Finally, the obtained results are discussed and some recommendations for future research have been made.
- ItemNávrh nadzvukového aerodynamického tunelu(Technická Univerzita v Liberci, 2014) Kracík, Jan; Dvořák, VáclavTato práce se zabývá návrhem nadzvukového aerodynamického tunelu. Tunel se skládá z experimentálního variabilního měřicího prostoru a nové koncepce ejektoru. U měřicího prostoru je uvažováno s nadzvukovými tryskami pro tři různá Machova čísla. Dále je kanál měřicího prostoru upraven tak, aby bylo možné studovat vznik šikmých rázových vln a dalších procesů. Ejektor byl navržen s dvanácti kruhovými vyměnitelnými hnacími tryskami a předpokládanou maximální dosahovanou účinností 25%. Navržený ejektor a měřicí prostor byly numericky ověřeny v programu Ansys Fluent 15.0. Vyrobený a sestavený nadzvukový ejektor byl experimentálně proměřen pro různý počet současně zapnutých hnacích trysek.
- ItemOptimalizace procesu tepelného zpracování dílů převodovky z hlediska deformací(Technická Univerzita v Liberci, 2011) Kracík, Jan; Hotař, AdamThis thesis examines the impact of heat treatment on deformation of hole of driven wheel transmission. It is an evaluation of the measured results to design the optimal geometry of the processed parts to be suitable for quenching in oil and gas pressure quenching.