Analýza mechanických vlastností materiálů ULTEM zpracované pomocí technologie 3D tisku
dc.contributor | Vičař David, Ing. : 66282 | |
dc.contributor.advisor | Šafka Jiří, Ing. Ph.D. : 61635 | |
dc.contributor.author | Pajr, Aleš | |
dc.contributor.other | Manlig František, doc. Dr. Ing. Skolitel : 55383 | |
dc.contributor.other | Seidl Martin, Ing. Ph.D. Konzultant : 64391 | |
dc.contributor.other | Bene Tomáš, Ing. Konzultant2 : 65965 | |
dc.date.accessioned | 2019-02-03T08:56:13Z | |
dc.date.available | 2019-02-03T08:56:13Z | |
dc.date.committed | 2018-2-1 | |
dc.date.defense | 2017-8-29 | |
dc.date.submitted | 2016-11-1 | |
dc.date.updated | 2018-12-10 | |
dc.degree.level | Bc. | |
dc.description.abstract | Tato bakalářská práce se zabývá analýzou mechanických vlastností materiálu ULTEM 1010 z pohledu vlivu orientace 3D tisku zkušebních těles na výsledné mechanické zkoušky tahem. Zkoumaným materiál byl použit ULTEM 1010, který je velice pevný a má vysokou teplotní odolnost. Vlastní praktické testy probíhaly dle příslušné mezinárodní normy ČSN EN ISO 527. Výsledkem a přínosem této práce je porovnání mechanických vlastností zkoušky tahem tištených vzorků se vstřikovanými vzorky. | cs |
dc.description.abstract | This bachelor thesis deals with the analysis of mechanical properties of ULTEM 1010 material from the point of view of influence of 3D print orientation of test bodies on the result of mechanical pull tests. The tested material was ULTEM 1010, which is very strong and has high temperature resistance. Practical tests were carried out according to the relevant international standard ČSN EN ISO 527. The result and contribution of this work is the comparison of the mechanical properties of the test by drawing printed samples with injected samples | en |
dc.description.mark | ||
dc.format | 92 | |
dc.format.extent | Ilustrace, Grafy, Tabulky ROM, Grafy, Tabulky Namerene_sily_Fy_2017_Vojtech_Novák Namerene_sily_Fx_2017_Vojtech_Novák Mereni_teplot_2017_Vojtech_Novák Mereni_drsnosti_2017_Vojtech_Novák Fotografie_trisek_2017_Vojtech_Novak, Grafy, Tabulky 16 grafů, 1 , 1 tabulka | |
dc.identifier.uri | https://dspace.tul.cz/handle/15240/150897 | |
dc.language.iso | cs | |
dc.relation.isbasedon | [1] NOORANI, R. Rapid Prototyping: principles and aplications. Hoboken: John Wiley and Sons, 2006. ISBN 0-471-73001-7. | |
dc.relation.isbasedon | [2] JACOBS, P. F. Stereolithography and other RP and M technologies: from rapid prototyping to rapid tooling. New York: ASME Press, 1996. ISBN 0-87263-467-1. | |
dc.relation.isbasedon | [3] GIBSON, I., D.W. ROSEN a B. STUCKER. Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing. New York: Springer, 2010. ISBN 978-1-4419-1119-3. | |
dc.relation.isbasedon | [4] HOPKINSON, N., R. HAGUE a P. DICKENS. Rapid Manufacturing: An Industrial Revolution for the Digital Age. Chichester: Wiley, 2006. ISBN 978-0-470-01613-8. | |
dc.rights | Vysokoškolská závěrečná práce je autorské dílo chráněné dle zákona č. 121/2000 Sb., autorský zákon, ve znění pozdějších předpisů. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem https://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou https://knihovna.tul.cz/document/26 | cs |
dc.rights | A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act. https://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics https://knihovna.tul.cz/document/26 | en |
dc.rights.uri | https://knihovna.tul.cz/document/26 | |
dc.rights.uri | https://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf | |
dc.subject | 3D tisk | cs |
dc.subject | ULTEM 1010 | cs |
dc.subject | vlastnosti 3D materiálů | cs |
dc.subject | FDM | cs |
dc.subject | Tahová zkouška | cs |
dc.subject | Pevnost v tahu | cs |
dc.subject | Poměrné prodloužení | cs |
dc.subject | 3D print | en |
dc.subject | ULTEM 1010 | en |
dc.subject | properties of 3D materials | en |
dc.subject | FDM | en |
dc.subject | Tensile Thrust | en |
dc.subject | Tensile Strength | en |
dc.subject | Relative Extension | en |
dc.title | Analýza mechanických vlastností materiálů ULTEM zpracované pomocí technologie 3D tisku | cs |
dc.type | bakalářská práce | cs |
local.degree.abbreviation | Bakalářský | |
local.degree.discipline | SI | |
local.degree.programme | Strojní inženýrství | |
local.degree.programmeabbreviation | B2301 | |
local.department.abbreviation | KSA | |
local.faculty | Fakulta strojní | cs |
local.faculty.abbreviation | FS | |
local.identifier.author | S13000148 | |
local.identifier.stag | 35577 | |
local.identifier.verbis | ||
local.note.administrators | automat | |
local.poradovecislo | STARA PRACE |
Files
Original bundle
1 - 4 of 4
Loading...
- Name:
- bakalarska_prace_2017_Ales_Pajr.pdf
- Size:
- 2.74 MB
- Format:
- Adobe Portable Document Format
- Description:
- VSKP
Loading...
- Name:
- Pajr.pdf
- Size:
- 139.46 KB
- Format:
- Adobe Portable Document Format
- Description:
- Posudek_vedouciho_VSKP
Loading...
- Name:
- Pajr.pdf
- Size:
- 128.43 KB
- Format:
- Adobe Portable Document Format
- Description:
- Posudek_oponenta_VSKP
Loading...
- Name:
- Pajr.pdf
- Size:
- 61.48 KB
- Format:
- Adobe Portable Document Format
- Description:
- Prubeh_Obhajoby_VSKP