Browsing by Author "Dvořák, Václav"
Now showing 1 - 20 of 42
Results Per Page
Sort Options
- ItemApplying a variable geometry ejector in a solar ejector refrigeration system(Elsevier Ltd, 2020-05) Van Nguyen, Vu; Varga, Szabolcs; Soares, Joao; Dvořák, Václav; Oliveira, Armando CThis paper presents an experimental study of the influence of a variable geometry ejector (VGE) design on the performance of a small-scale, 1.5 kW nominal capacity solar heat driven ejector air-conditioning system under real-life working conditions. Under variable operating conditions (e.g. solar radiation, ambient temperature) fixed geometry ejector performs poorly, therefore the objective of the present work was to prove the benefit of the VGE concept. In the experimentally tested VGE the area ratio through a movable spindle (SP) and the nozzle exit position (NXP) can be adjusted in order to respond to the operating conditions. The results showed very stable operation of the cooling cycle during the experiments. Both NXP, SP had considerable influences on the cooling cycle performance. An optimal NXP was identified, which did not change with various operating conditions. Similarly, SP also showed an optimum; however, the optimum point depended strongly on the operating conditions. The results clearly indicated the benefit of using the VGE design over the fixed geometry. COP improvement was as high as 24% with a maximum of 0.29 corresponding to a cooling capacity of 1.6 kW when compared to a fixed geometry ejector. The study also confirmed the importance of using a variable-speed pump in the ejector cycle.
- ItemCFD Based Design for Ejector Cooling System Using HFOS (1234ze(E) and 1234yf)(MDPI, 2020) Elbarghthi, Anas F A; Mohamed, Saleh; Nguyen, Van Vu; Dvořák, VáclavThe field of computational fluid dynamics has been rekindled by recent researchers to unleash this powerful tool to predict the ejector design, as well as to analyse and improve its performance. In this paper, CFD simulation was conducted to model a 2-D axisymmetric supersonic ejector using NIST real gas model integrated in ANSYS Fluent to probe the physical insight and consistent with accurate solutions. HFOs (1234ze(E) and 1234yf) were used as working fluids for their promising alternatives, low global warming potential (GWP), and adhering to EU Council regulations. The impact of different operating conditions, performance maps, and the Pareto frontier performance approach were investigated. The expansion ratio of both refrigerants has been accomplished in linear relationship using their critical compression ratio within ±0.30% accuracy. The results show that R1234yf achieved reasonably better overall performance than R1234ze(E). Generally, by increasing the primary flow inlet saturation temperature and pressure, the entrainment ratio will be lower, and this allows for a higher critical operating back pressure. Moreover, it was found out that increasing the degree of superheat for inlet primary flow by 25 K improved the entrainment ratio by almost 20.70% for R1234yf. Conversely, increasing the degree of superheat to the inlet secondary flow has a relativity negative impact on the performance. The maximum overall ejector efficiency reached was 0.372 and 0.364 for R1234yf and R1234ze(E) respectively. Comparing the results using ideal gas model, the ejector entrainment ratio was overestimated up to 50.26% for R1234yf and 25.66% for R1234ze(E) higher than using real gas model.
- ItemExperimental investigation of centrifugal fans for personal protection equipment – effect of used 3D printing technologies(EDP Sciences, 2018) Dvořák, Václav; Kracík, Jan; Votrubec, Radek; Šafka, JiříThe aim of the research is experimental investigation of centrifugal fans for a personal protection equipment. The aim of the fan is to drive the contaminated air containing harmful or irritating particles through the filters and then into the mask of workers, such as a fireman, a labourer or a lab worker. The fan is measured on the test stand, the characteristics and performances are evaluated, i.e. the dependencies of the working pressure on the flow rate. The characteristics are measured for three constant speed settings. The characteristics of the wheels produced by the different 3D printing technology are compared. It is found that the production technology has only a minimal effect, the performance of the wheels is more influenced by the position of the impeller on the motor shaft and hence by the mutual position of the impeller and the diffuser.
- ItemHFO1234ze(e) as an alternative refrigerant for ejector cooling technology(MDPI, 2019-10-24) Nguyen, Van Vu; Varga, Szabolcs; Dvořák, VáclavThe paper presented a mathematical assessment of selected refrigerants for the ejector cooling purpose. R1234ze(e) and R1234yf are the well-known refrigerants of hydrofluoroolefins (HFOs), the fourth-generation halocarbon refrigerants. Nature working fluids, R600a and R290, and third-generation refrigerant of halocarbon (hydrofluorocarbon, HFC), R32 and R152a, were selected in the assessment. A detail mathematical model of the ejector, as well as other components of the cycle, was built. The results showed that the coefficient of performance (COP) of R1234ze(e) was significantly higher than R600a at the same operating conditions. R1234yf’s performance was compatible with R290, and both were about 5% less than the previous two. The results also indicated that R152a offered the best performance among the selected refrigerants, but due to the high value of global warming potential, it did not fulfill the requirements of the current European refrigerant regulations. On the other hand, R1234ze(e) was the most suitable working fluid for the ejector cooling technology, thanks to its overall performance.
- ItemHodnocení vlastností membrán pro entalpické výměníky tepla(Technická Univerzita v Liberci, 2015) Nguyen Van, Vu; Dvořák, VáclavCíl práce je zaměřen na hodnocení vlastností membrán pro výrobu entalpického výměníku tepla. Byly použity experimentální metody pro měření dvou nejdůležitějších vlastností membrán, kterými jsou transport vlhkosti a prodyšnost. Úvodní část práce seznamuje s problematikou výměníků tepla, základními pojmy o principy přestupu vlhkosti a prodyšnosti, rovněž je uvedena recenze literatury o entalpických výměnících. V další části práce je uvedeno uspořádání a popis zařízení k měření těchto dvou vlastností. Dále se práce zaměřuje na samotné měření a vyhodnocení získaných údajů.
- ItemIntroductory Numerical Study on Supersonic Ejector Working with R32(E D P SCIENCES, 17 AVE DU HOGGAR PARC D ACTIVITES COUTABOEUF BP 112, F-91944 CEDEX A, FRANCE, 2019) Vojta, Lukáš; Kracík, Jan; Dvořák, VáclavNowadays, there is an increasing demand for devices which work efficiently with the smallest possible consumption of energy. In this regard, incorporating ejectors seems to be an interesting choice. This paper describes the numerical analysis of the flow in a supersonic ejector working with R32 (difluoromethane) as the working fluid. The ejector geometry under investigation in this paper has already been experimentally analysed, however, air was used as the working fluid. Therefore, this paper deals with a numerical analysis of the same geometry but with a different working fluid. Furthermore, the design of the ejector enabled the adjustment of a particular distance of the motive nozzle from the beginning of the mixing chamber, i.e. the nozzle exit position (NXP). This work examines the ejector numerically for eleven values of back-pressure with the NXP of two millimetres; consequently, the performance line of the ejector with fixed boundary conditions at both inlets was obtained. Finally, the obtained results are discussed and some recommendations for future research have been made.
- ItemISO offshore kontejner pro přepravu zkapalněných technických plynů(Technická Univerzita v Liberci, 2012) Vorožcova, Jana; Dvořák, VáclavThe thesis deals with the definition of the basic dimensions of the container for liquefied industrial gases. The first section is a brief description of the equipment and the purpose of its operation. In addition, here is also enumeration by relevant international and industrial standards and regulations The second section describes in detail the work principle of the cryogenic tank, and the determination of basic parameters of the container. The third section contains the results of the measurements made during performance tests.
- ItemLaboratorní měření spalného tepla kapalných a tuhých paliv(Technická Univerzita v Liberci, 2015) Kovač, Vladimír; Dvořák, VáclavTato práce pojednává o problematice stanovení spalného tepla, na dvou různých typech kalorimetru. Byla provedená rešerše literatury a následné uvedení přístrojů do provozu. Dále byla provedena měření na jednotlivých kalorimetrech a zpracovány naměřené hodnoty. Pro každý kalorimetr byl vytvořen návod na měření úlohy. Kalorimetry byly porovnány mezi sebou a určeny jejich výhody a nevýhody. Naměřená data byla statisticky vyhodnocena.
- ItemLaboratorní měření tepelné vodivosti látek(Technická Univerzita v Liberci, 2015) Simet, Martin; Dvořák, VáclavBakalářská práce se zabývá měřením tepelné, teplotní vodivosti a popisem měření různými metodami. Metody jsou rozděleny na stacionární, absolutní, relativní a nestacionární. Praktická část je věnována měřícím přístrojům C-Therm a Lambda HFM 436/1E, provedení vlastního měření a vyhodnocení výsledků. V příloze jsou vytvořeny návody na měření pro tyto přístroje.
- ItemLaboratorní měření viskozity kapalin(Technická Univerzita v Liberci, 2015) Kotyk, Pavel; Dvořák, VáclavTato bakalářská práce je zaměřená především na viskozitu a její laboratorní měření. Vysvětluje metody, kterými se viskozita měří a popisuje vybrané viskozimetry. Jejich principy a návody k použití. Nechybí měření na obou viskozimetrech, porovnání výsledků a zhodnocení výhod a nevýhod. Cílem bakalářské práce bylo vytvořit dokument použitelný jako návod k měření viskozity.
- ItemMeasurement and calculating of supersonic ejectors(E D P SCIENCES, 17 AVE DU HOGGAR PARC D ACTIVITES COUTABOEUF BP 112, F-91944 CEDEX A, FRANCE, 2019) Vojta, Lukáš; Dvořák, VáclavThis paper deals with numerical and experimental investigation of the flow in an air to air supersonic ejector with constant area mixing chamber. The mixing chamber of previous ejector was completely repaired since a scratch from previous turning had been found. As a result, a new geometry of the mixing chamber was created. Several measurements were conducted with different nozzle position (NP): 1 mm, 2 mm and 3 mm. Furthermore, for a given NP, two different values of stagnation pressure of 200 kPa and 300 kPa at the primary air inlet were investigated in more detail. All numerical simulations were performed in the ANSYS Fluent software. It was found that the influence of the position of the nozzle influences the ejection factor only to a certain extent. For the other parameters of the ejector is also a need to find the optimum position of the nozzle. Repair of the mixing chamber has contributed to reduce the pressure difference at the wall of the mixing chamber.
- ItemMěření charakteristik tepelného čerpadla voda - voda(Technická Univerzita v Liberci, 2015) Tran Xuan, Tay; Dvořák, VáclavTématem práce je proměřování výkonových charakteristik tepelného čerpadla voda - voda v prostorách laboratoří KEZ. Měření bude zaměřeno na zjištění závislosti topného faktoru a výkonů tepelného čerpadla na teplotách chladicí a ohřívané vody. Během práce byla provedena 5krát měření. Pro vyrovnání výsledků měření, byly naměřené hodnoty vyneseny pro bezrozměrnou teplotu T*, bezrozměrný průtok V* a bezrozměrný příkon Po *. Z vypočtených údajů jako výkony, faktory chladících a topných byly vypracovány grafy pro všech 5krát měření a pak vyhodnocení výsledky.
- ItemMěření entalpických deskových výměníků(Technická Univerzita v Liberci, 2013) Pavlas, Michal; Dvořák, VáclavV bakalářské práci je řešena problematika měření rekuperačních výměníků na experimentální trati. Vlastní práce je rozdělena na teoretickou a praktickou část, kde v teoretické části jsou uvedeny základní rozdělení výměníků a popsány vztahy definující jejich výkonost. Dále obsahuje popis stávající tratě a měření. V praktické části je porovnání aktuálního stavu tratě podle platných norem a uvedeno několik možných úprav ke zpřesnění metodiky měření na měřící trati. Je zde také uvedena nejistota měření, kterou je zatížená aktuální trať. V závěru je upozorněno na zjištěné nedostatky a je provedeno zhodnocení práce.
- ItemMěření rychlostních a turbulentních profilů v podzvukovém ejektoru metodou CTA(Technická Univerzita v Liberci, 2015) Dědeček, Jan; Dvořák, VáclavV naší práci se zabývame proudovými procesi v divergentní části směšovací komory. V první řadě jsme proměřili průběh statického tlaku podél směšovací komory a difuzoru. Pro určení tří režimů, které jsme po celou dobu proměřovali, jsme získali průběhy účinnosti a pracovní charakteristiky ejektoru. Poté došlo k naměření rychlostních a turbulentních profilů ve třech místech pro tři zvolené režimy. V poslední úloze jsme se pokusili popsat vliv generátoru syntetického paprsku při proudění ejektoru. Všechny naměřené veličiny jsme zanesli do diagramů. Pokusili jsme se porovnat rychlostní profily střední a fluktuační složky rychlosti. Porovnali jsme je buďto pro jeden režim ve třech místech nebo pro jedno místo všechny tři režimy.
- ItemMěření tlakově citlivými nátěry(Technická Univerzita v Liberci, 2011) Schmidtová, Veronika; Dvořák, VáclavThis thesis deals with development of PSP method ("pressure sensitive paint) in an aerodynamical experiment. It covers description of development of the system brought from DNW (Amsterdam) to Výzkumný a zkušební letecký ústav, a.s. (Aerodynamical Research and Test Institute) and few measurement campaigns. Especially it´s about an experiment in a transonic wind-tunnel, where the tests were held on a propeller profile F8. The experimental results are compared to a numerical counting in this thesis and also the uncertainty is evaluated.
- ItemMěření vzduchového ejektoru s divergentní směšovací komorou(Technická Univerzita v Liberci, 2014) Kasýk, Milan; Dvořák, VáclavPráce se zabývá funkčností a charakteristikami ejektoru. Cílem je přiblížit charakteristiky dvou různých ejektorů v závislosti na režimu měření. Režim měření je určen velikostí statického tlaku za difuzorem. Měřeno bylo na ejektorové trati, kde byl statický tlak odebírán ze stěny ejektoru a přiváděn k tlakovým senzorům. Naměřené hodnoty byly dále početně a graficky zpracovány. Tímto způsobem byly zobrazeny charakteristiky ejektorů, hmotnostní toky, ejekční poměr, poměr rychlostí, pracovní charakteristiky p4/p02, p4/p01 a účinnost, pro všechny měřící režimy. V závěru jsou oba ejektory porovnány z hlediska těchto charakteristik. Lze konstatovat, že ejektor s rozšířením difuzoru 6° dosáhl lepší účinnosti než ejektor s rozšířením difuzoru 4°, což je zcela v souladu s odbornou literaturou.
- ItemNávrh a optimalizace ejektoru pro nadzvukový aerodynamický tunel(Technická Univerzita v Liberci, 2007) Kolář, Jan; Dvořák, VáclavDiploma thesis discourse on design and optimalization on an ejector for supersonic wind tunnel which is supposed to be installed in Department of power engineering´s laboratory. The potential of existing pressured air distribution pipeline and available ejector dimensions were obtained by means of theoretical relations. Five basic concepts of ejector supersonic driving inflows were designed and computed using Fluent software. For folowing optimalization has been choosen a concept of twelve nozzles in mixing chamber perimeter and locally contracted diffuser. Numericall research was used to find the effects of inclination of driving nozzles on mixing processes and on driving air consumptition. The ejector with twelve driving nozzles inclined at an angle of 3° towards the ejector axis together with the narrowing mixing chamber gained the best results in efficiency.
- ItemNávrh a ověření měřicí tratě pro výzkum supersonických ejektorů(Technická Univerzita v Liberci, 2016) Guanlao, Anjelynn Mae Saligao; Dvořák, VáclavThe study of supersonic ejectors was conducted to be able to design and verify a test rig for research purposes. All components of the test rig was designed and manufactured. The design was verified using analytical and numerical simulation. The analytical solution used a one-dimensional, steady state approach. Losses in nozzles, diffuser, and friction effects were accounted for. The numerical simulation was done using the commercial software ANSYS Fluent.
- ItemNávrh hydraulické měřicí tratě pro stanovení průtokových charakteristik vodních čerpadel a armatur(Technická Univerzita v Liberci, 2015) Dostál, Petr; Dvořák, VáclavCílem této práce je návrh měřicí trati, změření průtoku a teploty na laboratorní trati TUL pomocí průtokoměru SIEMENS a pomocí clony vyvolávající tlakovou ztrátu, stanovení tlakových potrubních ztrát na trati se škrticím ventilem, stanovení charakteristiky čerpadla a potrubní trati a následný návrh chlazení potrubní trati.
- «
- 1 (current)
- 2
- 3
- »